BTS3118DATMA1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-252-3, DPak (2 Leads + Tab), SC-63 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| Series | HITFET® |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 2 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin (Sn) |
| Max Power Dissipation | 21W |
| Technology | MOS |
| Terminal Position | SINGLE |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 12V |
| Terminal Pitch | 2.28mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | BTS3118 |
| Pin Count | 4 |
| JESD-30 Code | R-PSSO-G2 |
| Number of Outputs | 1 |
| Qualification Status | Not Qualified |
| Output Voltage | 42V |
| Output Type | N-Channel |
| Max Output Current | 2.4A |
| Interface | On/Off |
| Output Configuration | Low Side |
| Power Dissipation | 21W |
| Output Current | 2.4A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Halogen Free | Halogen Free |
| Drain to Source Voltage (Vdss) | 42V |
| Nominal Input Voltage | 42V |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 42V Max |
| Max Dual Supply Voltage | 42V |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Over Voltage |
| Output Peak Current Limit-Nom | 15A |
| Rds On (Typ) | 70m Ω |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL |
| Height Seated (Max) | 2.5mm |
| Length | 6.5mm |
| Width | 6.22mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
BTS3118DATMA1 Overview
A Tape & Reel (TR) is used to package it.There is a TO-252-3, DPak (2 Leads + Tab), SC-63 package that includes it.A Surface Mount mounting is used for the LED driving board.The switch type of this switch is General Purpose.In order to guarantee reliable performance, the temperature should be set to -40°C~150°C TJ.It is possible to use 1 outputs in the lighting driver.To operate, it needs a supply voltage of Not Required.A maximum output voltage of N-Channel volts can be achieved by this LED driver.This object belongs to the BTS3118 family.It consists of 2 terminations in total.There are 1 functions of the LED driver.In order to meet the operation criteria, the maximum output current drops to 2.4A.Supply voltages of 12V allow for high efficiency.In this case, it is mounted in the way of Surface Mount.The LED driving board is equipped with a total of 4 pins.This electrical component can be found in the HITFET? series.The output current is set to 2.4A in this case.
BTS3118DATMA1 Features
Supplied from 12V
BTS3118DATMA1 Applications
There are a lot of Infineon Technologies BTS3118DATMA1 Power Switches ICs applications.
- Notebook and Tablet Computers
- Mobile Communication Devices
- Gaming
- Portable Music Players
- Hot-Swap Systems
- PDAs
- Telecom and Network Systems
- Wearable Devices
- Hard Disk Drives
- Wireless Headsets
