8 Terminations5V 8 Pin MAX485 Receivers1 Bits 1/1 Drivers/Receivers1 Functions

  • Manufacturer: Maxim Integrated
  • Nocochips NO: 503-MAX485EPA+
  • Package: 8-DIP (0.300, 7.62mm)
  • Datasheet: PDF
  • Stock: 814
  • Description: 8 Terminations5V 8 Pin MAX485 Receivers1 Bits 1/1 Drivers/Receivers1 Functions(Kg)



Factory Lead Time 1 Week
Contact Plating Tin
Mount Through Hole
Mounting Type Through Hole
Package / Case 8-DIP (0.300, 7.62mm)
Number of Pins 8
Weight 930.006106mg
Operating Temperature -40°C~85°C
Packaging Tube
Published 2010
JESD-609 Code e3
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 8
Type Transceiver
Subcategory Line Driver or Receivers
Technology CMOS
Voltage - Supply 4.75V~5.25V
Terminal Position DUAL
Peak Reflow Temperature (Cel) 260
Number of Functions 1
Supply Voltage 5V
Terminal Pitch 2.54mm
Base Part Number MAX485
Pin Count 8
Operating Supply Voltage 5V
Power Supplies 5V
Interface RS-422, RS-485
Operating Supply Current 500μA
Supply Current-Max 0.9mA
Data Rate 2.5Mbps
Output Characteristics 3-STATE
Differential Output YES
Protocol RS422, RS485
Number of Drivers/Receivers 1/1
Driver Number of Bits 1
Receiver Number of Bits 1
Duplex Half
Receiver Hysteresis 70mV
Number of Transceivers 1
Receive Delay-Max 200 ns
Simplex/Duplex Half Duplex
Transmit Delay-Max 60 ns
Output Low Current-Max 0.004A
Height 4.572mm
Length 9.91mm
Width 7.87mm
Radiation Hardening No
RoHS Status ROHS3 Compliant
Lead Free Lead Free

MAX485EPA+ Overview

LED drivers with the enhanced 8-DIP (0.300, 7.62mm) package will be able to drive a variety of common LEDs with ease.The receiver is packaged in a Tube package.This Transceiver can transceiver is a versatile part that has enabled many solutions to serve a variety of purposes.PCB or development board with Through Hole-type connectors can accommodate this wide receiver.With respect to the power supply, this differential driver uses 4.75V~5.25V.Up to 1/1 receivers/drivers can be installed simultaneously on this electronic part.Applications with operating temperatures of -40°C~85°C have been designed primarily for this ic receiver.An operating voltage range of 5V is suitable for this line driver ic.In this wide receiver, 8 terminations are integrated for driving and receiving signals from data.ICs that are packaged with market standard pinouts are available on the market.This part number MAX485 can be used to search for more variants based on the product type, temperature, package, etc.The driver IC has improved power dissipation control.A combination of optical transceiver downsizing and high-density Through Hole mounting reduces the package size dramatically.It provided a 1-bit resolution capability with this ic receiver.There are typically 1 bits of resolution specified in the specifications of this receiver.There is a voltage supply of 5V required in order for this transceiver module to be operated.It is possible to subcategoriLine Driver or Receiverse this rf transceiver module as Line Driver or Receivers.It is designed to be operated from a 5V power supply, so the module isolated transceiver will work effectively.There are 1 transceivers in total implemented by this IC.It is recommended that enough current be supplied to the VCC pin of the ic receiver, but not more than 0.9mA.With an input voltage of 500μA, this integrating circuit has the ability to drive LEDs with an output voltage of 500μA.

MAX485EPA+ Features

Tube package
8 pin count
8 pins
5V power supply

MAX485EPA+ Applications

There are a lot of Maxim Integrated MAX485EPA+ Drivers/Receivers/Transceivers applications.

  • Carrier phase observations
  • Tuner
  • Sensor reporting
  • Shortwave receiver
  • Aircraft navigation
  • Wireless communication
  • Cell phones
  • SONET/SDH Network
  • Desktop radio
  • Metro access rings

Write a review

Note: HTML is not translated!
    Bad           Good